Fastite Fittings Fastite

90° Bends: Fastite Bell-Bell1 3 4

Size
(in.)		 Pressure2
Rating
(psi)		 Dimensions in Inches Weight
(lbs.)
T A R
30 250 0.66 22.75 20.50 1290
36 250 0.74 25.75 23.50 1810
42 250 0.82 29.25 26.50 2784
48 250 0.90 33.25 30.50 3960
54 250 0.90 37.00 34.25 3750
60 250 0.94 39.50 36.50 4390
64 250 0.99 42.00 38.75 5170

60° Bends: Fastite Bell-Bell1 4

Size5
(in.)		 Pressure2
Rating
(psi)		 Dimensions in Inches Weight
(lbs.)
T A R
30 250 1.03 15.0 19.9 1415
36 250 1.15 28.0 42.4 2780
42 250 1.28 31.0 42.5 3315
48 250 1.42 24.0 35.5 3505
54 250 0.90 24.0 36.8 3115
60 250 0.94 24.0 36.4 3495
64 250 0.99 30.0 46.3 4520

45° Bends: Fastite Bell-Bell1 3 4

Size
(in.)		 Pressure2
Rating
(psi)		 Dimensions in Inches Weight
(lbs.)
T A R
30 250 0.66 10.5 19.92 1010
36 250 0.74 12.0 23.54 1395
42 250 0.82 14.0 27.20 2235
48 250 0.90 15.0 29.60 2960
54 250 0.90 20.28 42.32 2890
60 250 0.94 21.26 44.08 3335
64 250 0.99 22.24 45.85 3865

30° Bends: Fastite Bell-Bell1 4

Size5
(in.)		 Pressure2
Rating
(psi)		 Dimensions in Inches Weight
(lbs.)
T A R
30 250 1.03 15.0 42.90 1455
36 250 1.15 18.0 54.10 2210
42 250 1.28 21.0 65.30 2610
48 250 0.90 11.0 30.79 36706
54 250 0.90 16.0 49.40 2585
60 250 0.94 19.0 59.70 3180
64 250 0.99 18.5 56.90 3545

22 1/2° Bends: Fastite Bell-Bell1 3 4

Size
(in.)		 Pressure2
Rating
(psi)		 Dimensions in Inches Weight
(lbs.)
T A R
30 250 0.66 6.75 22.60 900
36 250 0.74 7.75 27.70 1220
42 250 0.82 9.00 31.40 1972
48 250 0.90 10.00 36.50 2630
54 250 0.90 10.24 37.65 2125
60 250 0.94 10.63 38.36 2425
64 250 0.99 11.02 39.06 2785

22 1/2° Bends: Fastite Bell-Bell1 3 4

Size
(in.)		 Pressure2
Rating
(psi)		 Dimensions in Inches Weight
(lbs.)
T A R
30 250 0.66 4.75 25.40 830
36 250 0.74 5.00 27.90 1100
42 250 0.82 6.00 33.00 1934
48 250 0.90 6.50 33.50 2350
54 250 0.90 6.50 38.07 1820
60 250 0.94 7.00 40.61 2095
64 250 0.99 7.00 38.07 2375

1 Bends can be furnished with Fastite plain ends.

2 Higher pressure ratings are available on special applications. Pressure ratings may be limited below the values shown by the pressure rating of the pipe to which fitting is attached, or the restrained joint used. Based on performance testing per AWWA C153, AMERICAN can rate 30"-48" C153 bends 350 psi. Consult AMERICAN.

3 30"-48" Fastite and Flex-Ring bends can have the same appearance (both have basic cross-section of top middle “cut”).

4 AWWA C153 configurations with lesser weights and dimensions may be furnished in some sizes at Foundry option. Consult AMERICAN.

5 Smaller sizes are available on special applications. Consult AMERICAN.

6 Fastite fittings with these weights have different dimensions than shown in the table above. Consult AMERICAN when dimensions are critical.

Request More Information

Add specific model info if applicable

Tell us more

Print Page